Tio1608-D2 I/O Rack

		Tio1608-D2
General specifications
Sampling frequency rate	External	44.1kHz, 48kHz, 88.2kHz, 96kHz
Signal delay		Less than 1.3ms INPUT to OUTPUT, connect with DM3, Dante Receive Latency set to 0.25ms (one way), Fs=96kHz; Less than 2.6ms INPUT to OUTPUT, connect with DM3, Dante Receive Latency set to 0.25ms (one way), Fs=48kHz
Total harmonic distortion		Less than 0.2% +4 dBu@20Hz-20kHz into 600Ω, Gain=+66 dB / Less than 0.05% +4 dBU@20Hz-20kHz into 600Ω, Gain=-6 dB, INPUT to OUTPUT, Fs=88.2kHz, 96kHz; Less than 0.1% +4 dBu@20Hz-20kHz into 600Ω, Gain=+66 dB / Less than 0.05% +4 dBU@20Hz-20kHz into 600Ω, Gain=-6 dB, INPUT to OUTPUT, Fs=44.1kHz, 48kHz *Measured with a -18 dB/octave filter @80kHz
Frequency response		+0.5, -1.5 dB 20Hz-20kHz, refer to the nominal output level @1kHz, INPUT to OUTPUT
Dynamic range		108 dB, INPUT to OUTPUT, Gain=-6 dB / 110 dB, DA Converter, Fs 96kHz; 108 dB, INPUT to OUTPUT, Gain=-6 dB / 112 dB, DA Converter, Fs 48kHz
Hum & noise level	Equivalent input noise	-128 dBu, Gain=+66 dB, Fs 96kHz, 48kHz *Measured with A-weighting filter
Hum & noise level	Residual output noise	-86 dBu, Fs 96kHz / -88 dBu, Fs 48kHz, ST main off *Measured with A-weighting filter
Crosstalk		-100 dB, adjacent INPUT/OUTPUT channels, Input Gain = -6 dB *Measured with a -30 dB/octave filter @22kHz
Heat dissipation		100-240V, 50/60Hz, 43.5kcal/h
Power requirements		100-240V, 50/60Hz
Power consumption		50W
Dimensions	W	480mm (18.9”)
	H	88mm (3.5”)
	D	364mm (14.4”)
Net weight		5.7kg (12.6lbs)
Accessories		Owner’s Manual, Power Cord (2.5m), Rubber stoppers (4)
Others		Temperature Range: Operating temperature range: 0 - 40℃, Storage temperature range: -20 - 60℃

คุณลักษณะของอนาล็อกอินพุต

Input Terminals	GAIN	Actual Load Impedance	For Use With Nominal	Input Level			Connector	Balanced / Unbalanced
Input Terminals	GAIN	Actual Load Impedance	For Use With Nominal	Sensitivity ^*1	Nominal	Max. before clip	Connector	Balanced / Unbalanced
INPUT 1-16	+66 dB	7.5kΩ	50-600Ω Mics & 600Ω Lines	-82 dBu (61.6μV)	-62 dBu (0.616mV)	-42 dBu (6.16mV)	Combo Jack (XLR-3-31 type ^2 or TRS phone ^3)	Balanced
INPUT 1-16	-6 dB	7.5kΩ	50-600Ω Mics & 600Ω Lines	+10 dBu (245mV)	+10 dBu (2.45V)	+30 dBu (24.5V)	Combo Jack (XLR-3-31 type ^2 or TRS phone ^3)	Balanced

สำหรับสเป็คเหล่านี้ 0 dBu = 0.775Vrms
จ่ายแรงดันไฟฟ้า +48V DC (ระบบ phantom power) ให้กับขั้ว INPUT แบบ XLR ผ่านสวิตช์ควบคุมซอฟต์แวร์
*1. ค่าความไว หมายถึง ระดับต่ำสุดที่จะทำให้เกิดเอาต์พุท +4 dBu (1.23V) หรือ ระดับเอาต์พุทเมื่อตั้งค่าเกนไว้ที่ระดับสูงสุด
*2. 1: GND, 2: HOT, 3: COLD
*3. Tip: HOT, Ring: COLD, Sleeve: GND

คุณลักษณะของอนาล็อกเอาต์พุท

Output Terminals	Actual Source Impedance	For Use With Nominal	Output Level		Connector	Balanced / Unbalanced
Output Terminals	Actual Source Impedance	For Use With Nominal	Nominal	Max. before clip	Connector	Balanced / Unbalanced
OUTPUT 1-8	75Ω	600Ω Lines	+4 dBu (1.23V)	+24 dBu (12.3V)	XLR-3-32 type ^*1	Balanced

สำหรับสเป็คเหล่านี้ 0 dBu = 0.775Vrms
*1. 1: GND, 2: HOT, 3: COLD

คุณลักษณะของดิจิตอลอินพุทและเอาต์พุท

Terminal	Format	Data length	Level	Audio	Connector
Primary / Secondary	Dante	24bit or 32bit	1000Base-T	16ch (Tio1608-D2 to other devises) 8ch (Other devises to Tio1608-D2)	etherCON Cat5e